Can You Drill Out A Lock Cylinder?

Lock cylinders are commonly used to lock up your keyless entry system, or your car. If you ever get locked out of the house or your car, there’s no need to panic.

There are several types of cylinder locks on the market, and some are harder to pick than others. However, all locks can be drilled out, and it’s an easy DIY project anyone can complete.

If you have ever tried to drill out a lock cylinder yourself, you probably found it was easier said than done.

Consider using a drill press or a Dremel tool instead of using a regular drill. These tools allow you to control the speed and depth of your drilling. 

You should also buy a new set of a power tool that is designed specifically for lock cylinders.

Some of these tools even come with a special bit that allows you to drill into the lock without damaging the mechanism.

Keep on reading to know the extra steps on how to drill out ignition lock cylinder and safety tips when drilling.

Steps to Drill out Ignition Lock Cylinder

To drill out the ignition lock cylinder, you must first make sure your vehicle is locked and locked in a parking lot.

The following simple steps will show how:

Step 1 - Remove the old key

Remove all keys from your lock before starting any work on it. There are several methods available.

It depends on what kind of pin ignition system you have. Some locks use one large pin to hold everything together while others require 2-3 smaller pins.

Regardless of which type of locking mechanism you have, make sure that no other part has been damaged during the removal procedure.

Once you know that nothing else needs attention, you can safely proceed to step two.

Step 2 - Cut off your new key shanks

You may need to file again until you feel comfortable that the blade won’t snag anywhere as you try to insert it into the slot.

Step 3–Inserting the new key to your locking mechanism

That completes the process on how to drill motor out an ignition cylinder.

Safety precautions

Safety First: Always use safety glasses or goggles when drilling into the lock.

1. When drilling out the cylinder for an ignition lock, you should first turn the car off, disconnect it from the battery, and disconnect the negative cable.

2. To prevent injury, have a helper hold the key as you drill speed out the lock cylinder.

3. Keep the tip of a flathead screwdriver at a 90-degree angle when drilling out a lock cylinder to avoid scratching the cylinder.

4. If you are drilling the lock cylinder, the “right way” is to use an ignition key to drill it, which is the same as using a key to open it.

5. A power drill bit should drill out the ignition lock cylinder at the correct angle.

Final Thoughts

Using a drill machine to drill out the ignition lock cylinder could have saved you a lot of money and time.

You can also use a file to hammer the cylinder out, but a drill is a better option because a file can damage the lock cylinder.

If you’re going to use a drill to drill out the lock cylinder, have a second drill just in case the first one breaks, or you might have trouble getting the cylinder out.

Do You Need A Drill To Install A Door Knob?

Doors are an integral part of home design. They allow people in and out of their homes easily, and if you want to keep your doors looking new, there are several ways you can get the job done.

One way to improve the appearance of your door knobs is to install them correctly. While this may sound intimidating, there are tools you can use to make the process easier.

Yes, you will need a drill to install and make a door knob hole. Door handles are installed on the inside, which requires a drill to open the door.

In this article, I’ll show you the steps on how to drill a door knob hole and advantages of using a drill to make it.

How to Drill New Door Knob Holes?

For those who want to drill a hole in a door knob jig or specialty item such as a mason jar or bottle opener, the m2 dia. bit is the preferred solution.

Its small diameter makes it very versatile and you’ll want to purchase the best quality, high-quality m2 dia bit you can afford.

Steps to drill a door knob hole jig:

Step 1: Prep work before drilling

Before beginning any project, make sure everything is clean and dry. Use cleaning products specifically designed for surfaces made of steel, aluminum, copper and brass.

To drill a door knob hole, you will need:

Step 2: Using a drill, make sure you are in an area with enough stability to prevent the drill head from wobbling during the process. 

Step 3: Turn the handle so that the back side faces up. Using a pencil mark where the centerline should be placed. This helps when installing the screw later on.

Step 4: Place the tip of the drill into the hole at the top of the beautiful door knob. Slowly turn the dial until the bottom of the drill center bit touches the floor.

Step 5: Holding the drill firmly against the surface, slowly rotate the drill to create a smooth circular opening.

If you have trouble creating a perfect circle, try using different sized holes for knobs first. Once you find one size works well, continue making additional holes around the perimeter.

Step 6: Once finished, remove the drill and reattach the handle. Add more screws to secure the gorgeous glass knob assembly.

You now have a perfectly drilled door knob!

Advantages of using a Drill to make Door Knob Hole

A Drill is a powerful tool with a variety of uses; it can be used for a variety of tasks, such as changing locks and making door knobs and handles.

Drill bits and drill sets come with different bits and distinct sets of drill bits.

The benefits of using a drill for this type of work are:

What to consider?

If you’re thinking about installing or replacing doorknobs for your front entryway, it’s important that you understand what holes those knobs have before doing any drilling work.

The holes vary based on whether they’re mounted on interior or exterior doors; they also depend on where the handle goes.

When choosing between different styles of doorknob hardware, such as mortise locks versus lever style locks, consider these factors:

Final Thoughts

The drill really does a great job on those wood door handles, as well as those metal cabinet handles.

I would recommend this to those who want their drill to perform those tough drilling jobs, as well as those who just want a convenient tool to have at their disposal.

HandyToolsHome.com

HandyToolsHome.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.co.uk & Amazon.com.
linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram