A 5 point laser level is a type of laser level that is used for measuring distances up to five feet. The device has a built-in bubble level and an adjustable laser pointer.
But if you're looking for a simple way to measure the height of a wall, ceiling, or other surfaces, then you might want to consider using other versions of laser level instead.
They are much easier to use than traditional levels, and they're also cheaper.
A laser level is an essential tool for anyone who works with wood or contractor level jobs. It's also a useful tool for those who want to build furniture, install flooring, floor plan measurements, or even hang pictures.
Furthermore, there are many different versions of laser level that can be used. Some have only one beam; others have two laser beam technology. And some models come equipped with batteries while others require AC power from your outlet.
So before buying any type of laser level, make sure it will work best for your needs.
What is A 5-Point Laser Level?
A 5-Point Laser Level is an electronic device used for measuring angles and distances.
It is a tool used for measuring horizontal and vertical angles. It has a small red beam of light that shines on a target surface. When the sighting laser beam hits the layout target, it reflects back to the receiver where the angle is measured.
There are many different types of laser levels available in today’s market. Some modern laser level have multiple receivers while others only have one.
How To Use A 5 Point Laser Level
- To begin operating, first, make sure all batteries are charged.
- Next, place the transmitter at the top left corner of the base plate.
- Then move the receiver down until its centerline touches the bottom edge of the base plate.
- Finally, rotate the receiver counterclockwise so that the white dot lines up with the green arrow.
- Once this alignment occurs, press the power button located near the front right side of the receiver.
- You should hear a beep sound indicating that the system is ready to work.
To start working with the laser level:
- Position yourself directly under the transmitter.
- Place the tip of the receiver against the surface being measured.
- Now slowly turn the handle clockwise until the indicator lights stop flashing.
- If there is no indication of accuracy, try turning the handle slightly more.
- Repeat these steps until you reach 90 degrees from the starting position.
At this point, the measurement can be recorded by pressing the record button located next to the power switch. After recording the measurements, remove the receiver from the level surface being measured. Turn off the power switch and store them away.
Five-Point Self-Leveler Components
These devices consist of four components:
1) transmitter,
2) receiver,
3) leveling bubble,
4) carrying case.
- First, attach the receiver to the underside of the baseplate.
- Next, align the bubble over the desired spot.
- Then, adjust the bubble's elevation until the bubble stops moving.
- Finally, slide the bubble into the carrying case.
Transmitter
Most transmitters measure 0.5 inches. However, some may vary depending on their model.
Receiver
Some receivers are designed to fit onto flat surfaces; however, they must be placed perpendicular to the surface being measured. Other receivers require a slight tilt.
Bubble
Many bubbles are made out of plastic. Others are metal. Most manufacturers recommend using a bubble that has been tested for safety purposes.
Carrying Case
A carrying case helps protect your device during transport. It keeps it safe from damage caused by bumps in transit. Some cases even have wheels attached to make transporting easier.
How to Use Laser Levels
There are several ways to operate a laser level. You can either manually control the bubble’s movement or let the unit do the job automatically. If you choose manual operation, simply follow the instructions below. Otherwise, read through our automatic mode section.
Manual Operation
- Turn the power switch on and then press the “Start/Stop” button.
- Next, move the bubble up and down until the light flashes. When the light turns solid again, the bubble is at its highest point.
- Repeat this process until the bubble reaches 90 degrees from the lowest point.
- At this point, the reading can be saved by pushing the record button.
- Finally, remove the receiver from its mounting location and put everything back inside the carrying case.
Automatic Mode
- Press the start/stop button once before turning on the power switch.
- Then, turn the power switch on and wait about 30 seconds.
- Once the time elapses, begin moving the bubble up and down.
- As soon as the light begins flashing, stop moving the bubble.
- Continue doing so until the light goes solid again. That means the bubble reached 90 degrees from the lowest position.
- Record the readings with the push of a button.
- Remove the receiver from its mounting spot and store it away.
Once you've used your new laser level, take advantage of all the features available. For example:
• Adjustable Height - A laser level can be adjusted to different heights based on where you're working. Simply raise or lower the bubble accordingly.
• Angle Indicator - An angle indicator shows how much the bubble needs to be tilted to reach an exact measurement.
• Auto-Level - Automatic leveling makes measuring uneven floor quick and simple. Just aim the straight beam along the line's edge and the laser level does the rest.
• Calibrate - To ensure accuracy, calibrating your laser level ensures that measurements taken are accurate.
• Compass - With a compass built into most units, you don't need to worry about getting lost.
• Depth Measurement - Measuring depth requires no special tools. All you need is a laser level.
• Distance Meter - Most lasers have distance meters that measure distances between two points.
• Dual Beam Technology - Some levels feature dual beams allowing you to see both sides of the workpiece simultaneously.
• Focusing System - Using focusing systems helps eliminate bubbles caused by uneven surfaces.
• Interference Detection - Detecting interference prevents false readings when using multiple receivers.
• Light Source - Different types of lights provide varying amounts of illumination.
We hope these tips help you get started with your own laser level.
Other pages if you're reading up on laser levels..
- How to measure the floor using a laser tape measure
- How to use a laser level to hang pictures
- Why are green laser measure tapes more expensive than red ones
- What is the advantage of a green laser over a red one
- What is the main advantage of a laser level
- How to make a laser level
- How to use a 5 point laser level
- How to use a Bosch rotary laser level
- How to use a Stanley Cubix laser level
- How to calibrate a Bosch laser level
- What is a rotating laser level
- How to use a pipe laser level
- How to use a laser level for tiling
- How to use a The CST Berger laser level
- How accurate are laser levels
- What is the difference between red and green laser levels
- How to use a laser level to align fence posts
- How to adjust a laser level
- How to use a laser level
